personalized gifts for girlfriend Kindle Keeper Tutorial customized gifts for mom

 personalized gifts for girlfri     |      2020-03-30 22:11

Pin ItI know it’;s not Tuesday but I’;m changing things up a bit and posting this tutorial today. (I normally post my tutorials on tuesday…;).. Next Tuesday I’;m *hoping* to be able to have a much needed ?shop?update!

I got a Kindle a few years ago, and have loved it! When I saw they were coming out with a new one, I decided it was time to pass mine onto my daughter (less books to haul around at at school). ?The new one came this week and my old cover didn’;t fit it. I knew very quickly that it would need a cover to survive bouncing around in the depths of my very unorganized purse!

retro cushion covers

This project is a great scrap buster! ?I used some fabric I had left over from that sneak peek last week.

It’;s lined with fusible fleece and corduroy. ?I wanted something soft but was not in to mood to work with Snuggles/Minke. ?The corduroy gave it great softness without creating any bulk.

To keep it from getting dirty, I laminated the fabric first. Now I can just wipe it clean.

You will need:

2 piece of fabric for the front and back, each 6″;x8.5″;. (I used home decor weight)

2 pieces fusible fleece 6″; x 8.5″;

2 pieces iron on vinyl (buy it in a roll at the fabric store next to the wonder under), 6″; x 8.5″;

2 pieces iron on vinyl 4″; x 6″;

2 pieces fabric for flap 4″; x 6″;

2 pieces corduroy 6″; x 8.5″;

2 pieces 2″; wide ribbon 16″; long

Teflon foot. You MUST have this to sew on the iron on vinyl. trust me ??

**edited to add:.. As I’;ve been using this I think the measurements are a bit snugpersonalized gifts for girlfriend, IF you line it with anything heavy (like Minke, Snuggle, or thick corduroy I would recommend increasing your measurements by 1/2″;…; so 6.5″; x 9″;…;.

**note: if I were to make this project again, I would use a light weight fusible interfacing on the back of the corduroy pieces. ?They stretched a bit and could use some stabilization.

ALL seams are 1/4″; unless noted

First apply the iron on vinyl to your front and back pieces and flap and flap lining pieces. To do this, peel the vinyl off of the paper. KEEP THE PAPER.

Place the vinyl sticky side down onto the right side of the fabric.

Place the paper (you just peeled off the vinyl) shiny down on top of the fabric/vinyl. You will have the grid side up. Make sure that the vinyl is completely covered (unless you want a mess on your iron!) and iron.

KEEP your paper pieces, once I cut a 16×;16 piece of iron on vinyl and I kept the paper backing. ?That way its a big enough piece to press your project when you are done. You CAN iron on the vinyl afterwards, you just have to use the paper it came with to protect your iron!

Take one of your pieces of ribbon and pin it to the long side of one of your flap pieces. ?Stitch in place.

Using a spool of thread, trace a curve onto the 2 bottom corners of your flap. Place your flap and flap lining pieces together, stitch with a 1/4″; seam. ?Clip your corners and turn right side out. ?Press (remember to use your leftover paper).

Top stitch the edges. ?Set aside.

Using your leftover paper from your vinyl, iron the fusible fleece onto the wrong side of your 2 outside pieces.

Stitch your 2nd piece of ribbon onto your front piece. Stitch it 3″; in from the left edge (the edge the flap will be attached to) and centered. ?Stitch one straight stitch, then zig zag over the raw edge of the ribbon.

Fold the ribbon back and stitch in place. Make sure you back stitch.

Place front and back pieces together, right sides together. ?Round the 2 bottom corners as you did for your flap piece, and stitch a 1/4″; seam around the 2 sides and the bottom, leaving the top open. Clip your curves.

Stitch your 2 lining pieces together with 1/4″; seam, clip curves turn RIGHT side out and press.

Take your flap piece and slide it into your pouch. ?You will want the right side of your flap facing the BACK side of your pouch. Stitch in place.

Slide the lining piece into the pouch, the lining will be RIGHT side out and the pouch will be wrong side out. Pin well.

Stitch around the top opening. Starting at one side seam around the back of the pouch (the part that the flap is sewn to) and ending at the other side seam. Make sure you backstitch. Do not sew the front.

Turn right side out.

To close the opening on the front of the pouch, turn under and pin. Then topstitch in place.

Clip your strings and press! (remember to use your leftover paper piece, as long as you have that piece you can press out the wrinkles that will come as you sew)

Enjoy! I think these would make fun and easy gifts at Christmas time!

linking up:

There are some things in life we really can't live without and there are things that no stylish home should be without. The following home 'must haves' we are about to reveal are a good investment and yet some of them are not even that costly as you will find out! Furthermore, these classic pieces can be brought into all interior design styles and will never become dated.

When my son was small, I was always on the look out for fun Art Projects for Kids! Here’s a solution for what to do with kids art. Creative Contributor Colleen from Lemon Thistle?is in the thick of it with busy twin toddlers and a newborn. Today she’s showing us how she created art projects for kids to keep her littles engaged. Another great project with children is making these DIY Earth Day Crayons! And this Baby Shoe Growth Chart will keep those memories alive. This Jellyfish Windsock Craft is a good one too!

Everyone has a preferred sleep position.