personalized gifts for women How to Make a Barn Door Style Fireplace Screen pillow covers farmhouse

 personalized gifts for women     |      2020-01-19 21:14

Wondering how to make a barn door style fireplace screen? You have come to the ONLY place that I know of to teach you how to do it. As far as I can tell, this is a totally original DIY tutorial that I am super, super proud of :) I will warn you that this tutorial is long, but it's not because the project is particularly difficult–;it just has a lot of steps to explain. So don't be scared off. You can totally do this!

First, let me show you the image that inspired this project. I stumbled upon a Porch.com article that was featuring a home design project by Robin Chell Design; you can click here to see the whole home tour. The home includes this gorgeous sliding fireplace screen that was obviously professionally made by a super talented welder somewhere. I was literally SWOONING over it.

burlap pillow cover diy

The bad news was that my husband and I don't know how to weld, nor could we afford to hire the job out. So, we did what we always do…;we figured out how to DIY it without welding. Read on to learn how to make a barn door style, sliding fireplace screen. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy.

Materials Needed:

* Note that ourfinished fireplace screen measures 45″; x 32″;personalized gifts for women, which is sized to cover our large fireplace opening (42 1/2″; x 30 1/4″;). All of the materials and measurements below are specific to our fireplace. Simply alter the dimensions to fit your fireplace!*

*quantities needed are noted in parentheses*

Tools Needed:

Steps to build the screen portion:

**Review the diagram below before reading through all of the steps. It will help put the written steps into context for you**

1) Cut the hardware cloth to roughly 40” x 50” with your metal snips–;cutting it down makes it a bit easier to work with. After cutting it down, we placed a piece of plywood with some weights on top over night to helpget it to lay flat.

2) Separate the pulley wheels from the swivel mechanism (ours was easy to do–;we just has to remove the cotter pin). Use your high-heat spray paintto paint the hardware cloth, chrome spacers, washers, and pulley wheels black. We found black bolts so we did not have to paint them.

3) Next, cut the two 48”x 2”x 1/8” steel bars down to45” with the angle grinder and metal cutting wheel.

4) Next, cut the two 48” x 1 1/4” x 1/8” bars down to32″;. Clean up all cuts with a metal file if needed. Hold onto the 16″; pieces that you cut off these bars–;you need them for the next step.

5)Cut the 2 wheel posts (shown in pink in the diagram below) out of the pieces of 1 1/4” bars you cut off in the previous step. We cut our wheel posts down to 5 1/2” long. Then we used the wheels from the pulleys to trace the curve onto the top of each wheel post. We used our angle grinder to cut out the curve at the top of each wheel post.6) Now you are ready to assemble the screen door. Lay out the steel bars that make up the exterior of the fireplace screen. Mark the center of your corners using a pencil and painter's tape. Bear in mind that the top and bottom rails are the 2″; bars and are DOUBLED UP (one on each side of the screen). The narrower 1 1/4″; steel bars are used for the sides of the fireplace screen and are used only in front of the screen.

7) Use an electric drill to drill the holes for the bolts. We started with a small drill bit and worked up to the final diameter of 5/16”. Below is a picture of the different drill bits we used. This step is tedious, but believe it or not, it moves a little bit more quickly than trying to use a 5/16″; drill bit from the outset. To keep the process as streamlined as possible (and to prevent having to change the drill bits a zillion times), we drilled all the small holes at once and then moved up the next size drill bit to enlarge all the holes. We repeated the process until all the holes reached the 5/16″; size.

8) Once all your holes are drilled, layout the top of the frame (top rail, bottom rail and side rails) and place the screen/hardware cloth on top of it. We folded the edge of the screen over on the side edges about 1″; for added stability. Then place the back top and bottom rails on top of the screen.

9) Next, you need to feed the bolts through each part of the screen in this order: 1) the front top and bottom rails, 2) the side rails, 3) the screen (hardware cloth), 4) wheel posts and 5) the back top and bottom rails. Place a washer and nut on each boltand tighten. You are basically sandwiching the screen/hardware cloth and wheel posts between the two top rails and two bottom rails; the side rails are single rails–;they are not doubled-up like the top and bottom. The diagrams and photo below should help clarify this step.

10)Trim off any overhanging screenusing your metal snips.

11) Finally, you need to attach the pulley wheels to the wheel posts. Place a bolt through each wheel post, then add a washer, the pulley wheel, followed by another washer and finally a nut. Tighten.

Steps to attach the steel bar rail to the fireplace:

1) We attachedthe bottom of the rail 33” above the fireplace hearth to allow enough clearance for the screen to slide back and forth without dragging on the hearth. Use your assembled screenas your guide to determine how high to place your rail. Be sure it will have enough clearance to open and close.

2) We cut the two48” x 2” x 3/16” steel bars to 42” each. If your fireplace is smaller than ours, you may be able to use one continuous length of steel bar for your rail. Our fireplace is so wide that we had to split the rail into two separate steel bars.

3) Drill holes at 3”and 28” from the end using the same method as you did for the fireplace screen rails.

4) Hold your steel bar(s) up to your fireplace surface at the height you have determined is appropriate, using a level to ensure it's level. Use a marker or pencil to mark where holes need to be pre-drilled through the fireplace using the holes in the steel bar(s) as your guide.

5) After the holes weremarked, we pre-drilled holes following the instructions for the Tapcon screws using a hammer drill. We used Tapcon screws appropriate for our fireplace, which is brick covered with cement board and a thin cement overlay. You can read more about our DIY concrete fireplace here.

6) Next feedthe Tapcon screws through the steel bar rails,followed by the steel spacers. Then tighten the screws into place.

7) Finally use a touch of black paint to cover the blue on the Tapcon screws andhang your screen door on the rail by placing the pulley wheels on top of the rail.

That's it! Like I said, it's a lot of steps to learn how to make a barn door style fireplace screen, but it's really not difficult and the end result is AMAZING. Take a look.

We are so, so happy with how it turned out. What do you think? If you love it, be sure to pin it so that you can find it again later.

To achieve the look of traditional India you need to be thinking along the lines of rich warm colours, spicy shades and jewelled tones. Intricate patterns are fundamental, these can be shown in fabrics and curtains, luxury bedding and fret work. Be bold with pattern and strong colours, mix red, orange,lime, yellow and purple in one room, with accents of gold and silver to make the room shimmer and catch the sunlight.

What do you do with a chipped espresso cup? Make a pin cushion =) Since I have only have a few needles for hand sewing, I don’t want to lose them! And since the chipped part of the espresso cup was on the inside, I decided to make a home for my lonely needles =) It only took a few minutes to put together.

Hey friends! Today I am doing something a little bit different because I've gotten a lot of questions about cutting machines lately. I'm going to give you my 100% unbiased review of Silhouette vs. Cricut cutting machines. Now, I always share my honest opinions even in sponsored posts, but to eliminate ANY DOUBT, I have chosen to write this post as an unsponsored post. Neither company is compensating me in any way to write this post, nor would I want them to.I want everyone to be able to read this completely unbiased post and decide which cutting machine is best for them, because the answer may not be the same for everyone!